- #Custom maid 3d 2 english ui 4.2 irror how to#
- #Custom maid 3d 2 english ui 4.2 irror install#
- #Custom maid 3d 2 english ui 4.2 irror drivers#
- #Custom maid 3d 2 english ui 4.2 irror update#
- #Custom maid 3d 2 english ui 4.2 irror Pc#
If you already flashed this particular firmware to the printer and for any reason you like to re-flash the same bin file again to the printer, you need to rename it before you do this. Now one little remark that I need to make here. If everything looks fine, power the printer off.Ĭlose the display cover and remount the display.įrom the mainboard folder, copy the file starting with "Ender-3 v2" and ending with "bin" to the SD card. Power the printer on once more and wait until the printer is fully started and shows the main menu. Wait until the screen turns red, then power off the printer and remove the SD card from the display. Reconnect the display cable and power on the printer.
Now, take the SD card and insert it into the screen's SD card slot. Open the display case by removing the screws on the back. Power off the printer now and disconnect the display cable from the display.
Make sure that your SD card is not larger than 32 gigabytes, because the mainboard otherwise might not support reading it.
#Custom maid 3d 2 english ui 4.2 irror Pc#
Insert your SD card to your PC and Copy the DWIN_SET folder to the SD card.
#Custom maid 3d 2 english ui 4.2 irror update#
Yes, you hear me right, there is different firmware for the screen and the mainboard.įrom the official guides it says, always update the screen before the mainboard, so this exactly what we're going to do now. One is for updating the screen and one for the mainboard. In the new subfolder starting with "Ender-3 v2" you will find two subfolders for firmware. Using 7-zip, I am extracting the file to the current folder by right clicking the file and then selecting 7-zip → extract here. I've also linked to the official 7-zip download page here.
#Custom maid 3d 2 english ui 4.2 irror install#
Now, we download the right firmware and what we get from the Creality website is a RAR file, which is similar to a zip file but windows cannot handle it unless you install something like winrar or 7-zip, which is what I'm using. We're going to talk about the BLTouch installation in another video. The selection depends whether you have a BLTouch in combination with that mainboard or not. In my case, I would have to select one of the 4.2.2 firmware builds and if you have the 4.2.7, you would select one of these other builds. Here you see, there is different firmware versions for the different mainboards. Select the Ender series and then the Ender 3 v2. Head over to the support section and select "Firmware Download". Now that we know the mainboard version, let's head over to the crealit圓 website. They look identical except for the version number. Here on the left image you see, my printer has the 4.2.2 mainboard and this on the right is how the 4.2.7 looks like. To check, which mainboard version you have, there is no other way as to open up the electronics case and have a look at the mainboard itself.
#Custom maid 3d 2 english ui 4.2 irror drivers#
Why is this important? These two mainboard versions have different stepper motor drivers and require a different firmware. On the Ender 3 v2, this can be done in the printer menu, navigating to the Info screen, where you will find the current firmware version number.Īnother thing you need to know is, which mainboard version your printer has.Īpparently, Creality released Ender 3 v2 models with a 4.2.2 mainboard and newer builds may have the 4.2.7 mainboard. To figure if you should update, the first thing is to check the currently installed firmware version. The following process not only applies to the official Creality firmware but also to custom firmware, like Marlin or Klipper or anything else. Well, mainly because especially in the beginning, when a printer is released, it may contain some bugs and new firmware will usually address those issues and sometimes a new firmware version will also add new features.
Why should you keep your firmware up to date? In the Ender 3 v2 review video, I mentioned that I updated the firmware to the latest version from Creality.Īctually, I did this two times because Creality released new firmware versions during the test period. In the last couple of weeks, I've extensively tested the Ender 3 v2 for print quality and long term results and if you've missed that review, I've linked it here for you to check it out.
#Custom maid 3d 2 english ui 4.2 irror how to#
In this article, I will show you how to upgrade the firmware on your Ender 3 v2.Īlternatively you may want to watch the video, embedded above. Daniel Crosslink, welcome back to the channel and the blog.
0 kommentar(er)
